Rolling Wedge Milling Tools
Asphalt Milling Teeth Built to Outlast Carbide Picks
Rolling Wedge rolling carbide cutters bolt onto your planer attachment or road mill. One tool cuts asphalt, concrete and many grades of rebar.
- Guaranteed 10 to 1 tool life over carbide picks in asphalt
- Change a full 24-inch drum in 20 minutes, not 1-2 hours
- No bounce, no chatter, less vibration on your machine
Patented rolling-wedging-lifting tools made in Peoria, Illinois and sold direct in the USA.
Prefer to talk? Call +1 (309) 322-1600
Request Milling Tool Pricing
Tell us your machine and drum size. We'll send pricing and the right tool setup.
Why contractors switch from carbide picks
Far fewer tool changes
Replace tools every 1 to 3 months instead of twice a week. That is more milling time and less wrench time.
One tool for mixed surfaces
Mill asphalt and concrete in the same pass. No stopping to swap tooling when you hit concrete or rebar.
Cuts rebar without jamming
The rolling action slices through many grades of rebar, wire mesh and some dowel bars without stalls or broken tools.
Easier on your machine
Rolling, bounce-free travel cuts vibration. That protects hydraulic components and reduces operator fatigue.
Cleaner milled finish
Nine carbide teeth per tool spread the load evenly, so you get a smooth, consistent milled surface and uniform spoils.
Know your savings first
Use our online Milling Cost Comparison Tool to compare pick costs against Rolling Wedge before you buy.
How Rolling Wedge milling teeth work
Traditional carbide picks hammer and chisel the surface. Rolling Wedge tools roll instead. The rolling-wedging-lifting action uses the low tensile strength of asphalt and concrete, so the tool wedges and lifts material away with far less resistance.
Each tool carries nine carbide teeth around a rolling wheel and shaft. Wear spreads across the whole cutting radius instead of one point. The tools keep rotating, stay cooler than picks and need no water to run.
- Rolling Wedge Carbide Cutter (RW103-B) and RW127-B Milling Tool Mounts
- Tool diameters: 2.5 inch for skidsteer platforms, larger sizes for big road mills
- Nine carbide teeth per tool with a convex radiused cutting profile
- Milling drums in 18, 24, 30 and 40 inch cut widths
- End picks, flighting and mounting hardware available
- Fits rubber-tire and track skidsteer planer attachments: Bobcat, Caterpillar, Kubota, Roadhog, Simex, Virnig
- Upgrades for large mills on Roadtec, Caterpillar and Wirtgen platforms
- No water needed to keep tools rolling; water only for dust control
- Quantity-tiered pricing available
What happens next
Send your details
Tell us your machine, planer attachment and drum size. Add your current pick usage if you know it.
We match your setup
Our team confirms the right Rolling Wedge tools, mounts or drum for your equipment and application.
You get pricing
We send quantity-tiered pricing. Qualifying customers can also ask about the 20-day Try & Buy drum evaluation.
Frequently asked questions
How much do Rolling Wedge asphalt milling teeth cost?
Pricing is available on request and quantity-tiered discounts apply. Send us your machine and drum details and we will quote your setup. You can also use the online Milling Cost Comparison Tool to estimate savings against carbide picks.
Will these fit my cold planer or milling machine?
Rolling Wedge tools mount to skidsteer planer attachments from Bobcat, Caterpillar, Kubota, Roadhog, Simex and Virnig, and upgrade large mills on Roadtec, Caterpillar and Wirtgen platforms. Tell us your model and we will confirm fit.
How long do the tools last compared to carbide picks?
Rolling Wedge Milling Tools are guaranteed to outlast carbide picks 10 to 1 in the same asphalt milling environment. Typical replacement is every 1 to 3 months instead of twice a week.
Can they cut concrete and rebar too?
Yes. The same tool mills asphalt, concrete, wire mesh and rebar-reinforced concrete, and many grades of rebar and some concrete joint dowel bars, in a single pass with no tool swaps.
Can I try them before buying?
A limited Try & Buy program offers a 20-day Rolling Wedge Milling Drum evaluation for qualifying customers. It is an evaluation, not a general rental program. Ask us if you qualify.
Do you sell outside the USA or do milling work?
Rolling Wedge sells direct across the United States from Peoria, Illinois. We manufacture and sell tooling only and do not perform milling, paving or road construction work.
Stop changing picks twice a week
Send us your machine and drum size. We will match the right Rolling Wedge milling teeth and send pricing.
- Guaranteed 10 to 1 tool life over carbide picks in asphalt
- Change a full 24-inch drum in 20 minutes, not 1-2 hours
- No bounce, no chatter, less vibration on your machine
Prefer to talk? Call +1 (309) 322-1600